"Hi... love your site and the stories!! I love old trucks and I am trying to locate a drivable good running 1940 Ford 3/4 or 1/2t truck. By chance  anyone you know have one they are willing to sell?" (Tom Moore, Shelburne, NH - USA)

 

"I need parts for my 1939 international pickup and was wondering where to look." (Jeremy, Hillsboro, ND - USA)
 

"I have a 1955 (Dodge) C3 pickup I'm restoring but can't find parts". (Jeff, Cozad, NE - USA)

 

"Mr Ceschin, I enjoyed the story about your truck. I am thinking about acquiring a 3600 1954 long bed. I was wondering if it was possible to put an efficient 4 or 6 cylinder under the hood with that size of truck. I am not really sure if the two models are totally different. I also would like to use it as a daily driver. Thanks again for the story. Regards". (Rogie, Los Angeles, CA - USA)

 

"I Have been looking everywhere for a 1949 - 1959 Studebaker diecast truck. I was wondering if you might have one or know of anywhere I might find one. Thank you for any information you would have." (Kim Garrison, Meridian, MS - USA)

 

"I have property outside of Reno, NV and on purchase of property here sits an International vehicle. Not knowing how to get any info I thought I would email you. Steering wheel is on the right. It looks more like a mail carrier. Please help greatly appreciated." Danny, Sun Valley, NV

 

"Is there a market for 50s & 60s International Big Rig parts? I have several truck cabs, fenders, grills, hoods, etc. that have been stored in my warehouse for 40+ years. Should I scrap them or can I find a buyer?" Tim, Cleveland OH

 

"I own a 1953 Ford F100 all original w/ 289 V8 flathead 3 on tree. Its partly restored as I am a carpenter and the construction trade slowed way down. Unfortunately the funds are not there now. I have a nice 1,000 sqft shop that I would love to be put to good use restoring cars and trucks to help offset the cost to finish my project and somehow make money on it in movies. I'm open for ideas. Please help if you have any suggestions or needs. Thank you." - Kenny, Melrose FL

 

"I'm looking for a grill for a 1938 Fargo truck that I am restoring. It has 61,000 original miles. I would like to see others." - Keith, Goulburn, Australia

 

"I have had the opportunity to be given a 1927 1Ton Diamond Reo/Diamond T Truck - Model 723 6 cyl diesel truck. Would there be much value in it after it is restored? The truck is in good condition. Approximate cost to restore? Any written resources to help with this? Thanks." - Al Walton, Cedar Rapids, IA

 

"My 51 Ford F-1 was improperly stored at a local body shop and the coolant froze and cracked the block. I need a Flathead V8 replacement. Prefer a 24 stud. A short block would be ok." - Randy, Portland, OR

 

"I have an old hood off car or truck from what I believe is to be in the 30's era but I don't know for sure what it goes to nor do I have a need for it. I am looking for someone who can tell me what it is and wants to buy., thanks. I can email pics." - Steve, Salem, US

 

 

"I have an old utility trailer made out of a 1948 International pickup. It is the Knox bed and has that label on the tail gate. Would it be worth advertizing to sell it under restoration parts? Please advise." - Weston, Blackfood, ID

 

"Hi i was writing to ask is the cab of a 1955 s1 truck the same size as a pick up cab?" - Luke, Brisbane, Australia

 

"I am looking for the builders drawings for a 1941 Sterling "J" model truck. I want the dimensions if any available." - Gary, ??, USA

 

"I am having difficulty finding someone who can change out a differential ring gear on my 1939 Chevy 1/2 ton. The ring gear is riveted onto the differential case. One mechanic said it would not be as much of a problem to get the rivets out as it would be to find someone to install the new rivets. What type of a shop am I looking for? Any info will be appreciated." - Adrian, Corpus Christi, TX